dc-dc converters pola non-isolated 1 new product file name: ptv12010w.pdf rev (02): 19 dec 2005 2 year warranty all specifications ar e typical at nominal input, full load at 25 unless otherwise stated c in = 100 ? and 10 ? (ceramic), c out = 0 ? specifica tions *auto-track? is a trade mark of texas instruments the ptv12010 is a non-isolated dc-dc converter from artesyn under the point of load alliance (pola) standard. the vertical mounting option of the ptv12010 module provides performance in less than 20% of the space that is required by alternative solutions. the auto-t rack? feature provides for sequencing between multiple modules, a function, which is becoming a necessity for powering advanced silicon including dsps, fpgas and asics requiring controlled power-up and power-down. the ptv12010 has an input voltage of 10.8 vdc to 13.2 vdc and offers a wide 1.2 vdc to 5.5 vdc for suffix ?nd 0.8 vdc to 1.8 vdc for suffix output voltage range with up to 8 a output current, which allows for maximum design flexibility and a pathway for future upgrades. ? 8 a output current ? 1 2 v input voltage ? wide-output voltage adjust ? 1.2 vdc to 5.5 vdc for suffix ?nd 0.8 vdc to 1.8 vdc for suffix ? auto-track? sequencing* ? pre-bias start-up ? efficiencies up to 93% ? output on/off inhibit ? vertical through-hole mounting ? point-of-load-alliance (pola) compatible ? undervoltage lockout ? available rohs compliant ptv12010 12 vin single output output specifications voltage adjustability suffix 1.2-5.5 vdc (see note 4) suf fix 0.8-1.8 vdc setpoint accuracy (see note 8) ?.0% vo line regulation ?0 mv typ. load regulation ?2 mv typ. total regulation (see note 8) ?.0% vo minimum load 0 a ripple and noise suffix 20 mv pk-pk 20 mhz bandwidth suffix 15 mv pk-pk temperature co-efficient -40 o to +85 ? ?.5% vo t ransient response 70 ? recovery time (see note 5) overshoot/undershoot 100 mv input specifications input voltage range (see note 3) 10.8v-13.2 vdc input standby current 10 ma typ. remote on/off (see note 1) positive logic undervoltage lockout (increasing) 9.5 v typ. track input current pin 5 (see notes 6 and 7) -0.13 ma international safety standard approvals ul/cul can/csa-c22.2 no. 60950 file no. e174104 tv product service (en60950) certificate no. b 04 06 38572 044 cb report and certificate to iec60950, certificate no. us/8292/ul emc characteristics electr ostatic dischar ge en61000-4-2, iec801-2 conducted immunity en61000-4-6 radiated immunity en61000-4-3 general specifica tions efficiency see tables on page 2 insulation voltage non-isolated switching fr equency suffix 250-400 khz 325 khz typ. suffix 200-300 khz 250 khz typ. approvals and en60950 standar ds ul/cul60950 material flammability ul94v -0 dimensions (l x w x h) 22.86 x 8.38 x 10.16 mm 0.90 x 0.330 x 0.400 in weight 2.6 g (0.09 oz) mtbf telcordia sr-332 5,000,000 hours environmental specifications thermal performance operating ambient, -40 o to +85 ? (see note 2) temperature non-operating -40 o to +125 ? protection over cur r ent auto reset 16 a typ.
file name: ptv12010w.pdf rev (02): 19 dec 2005 for the most current data and application support visit www.artesyn.com/powergroup/products.htm dc-dc converters pola non-isolated 2 new product ptv12010 12 vin single output part number system with options product family point of load alliance compatible mounting v ersion v = vertical mounting style (9) d = horizontal through-hole (matte sn) h = horizontal through-hole (sn/pb) the ultra-wide output voltage trim range of fers major advantages to users who select the ptv12010. it is no longer necessary to purchase a variety of modules in order to cover different output voltages. the output voltage can be trimmed in a range of 1.2 vdc to 5.5 vdc for suffix ?nd 0.8 vdc to 1.8 vdc for suffix when the ptv12010 converter leaves the factory the output has been adjusted to the default voltage of 1.2 v for the ptv12010w and 0.8 v for PTV12010L. o o u u t t p p u u t t v v o o l l t t a a g g e e a a d d j j u u s s t t m m e e n n t t o o f f t t h h e e p p t t v v 1 1 2 2 0 0 1 1 0 0 s s e e r r i i e e s s output current 01 = 8 a input v oltage 12 = 12 v mechanical package always 0 ptv12010wah pin style a = through-hole std. pin length (0.150 output v oltage code w = wide l = low voltage efficiency t able - PTV12010L (i o = i omax ) output voltage efficiency vo = 1.8 v 87% vo = 1.5 v 86% vo = 1.2 v 84% v o = 1.0 v 81% vo = 0.8 v 78% efficiency t able - ptv12010w (i o = i omax ) output voltage efficiency vo = 5.0 v 92% vo = 3.3 v 90% vo = 2.5 v 88% v o = 1.8 v 85% vo = 1.5 v 83% vo = 1.2 v 80% n n o o t t e e s s 1 remote on/off . positive logic on: pin 7 open; or v > 2 v off: pin 7 gnd; or v < 0.6 v 2 see figures 1, 2, 3 and 6 for safe operating curves. 3 a 100 ? electrolytic input capacitor is required for proper operation as well as a 10 ? high--requency ceramic capacitor. the electrolytic capacitor must be rated for the minimum rms of ripple current. 4 an external output capacitor is not required for basic operation. adding 100 ? of distributed capacitance at the load will improve the transient r esponse. 5 1 a/ s load step, 50 to 100% i omax , c3 = 100 f . 6 if utilized vout will track applied voltage by ?.3 v (up to vo set point). 7 the pre-bias start-up feature is not compatible with auto-track?. this is because when the module is under auto-track? control, it is fully active and will sink current if the output voltage is below that of a back-feeding sour ce. therefore to ensure a pre-bias hold-off, one of the following two techniques must be followed when input power is first applied to the module. the auto-track? function must either be disabled, or the modules output held off using the inhibit pin. refer to application note 196 for more details. 8 the set-point voltage tolerance is af fected by the tolerance and stability of r set . the stated limit is unconditionally met if r set has a tolerance of 1% with 100/ o or better temperature stability. 9 to order pb-free (rohs compatible) through-hole parts replace the mounting option ?ith ??eg. ptv12010wad. 10 notice: some models do not support all options. please contact your local artesyn representative or use the on-line model number search tool at http://www .ar tesyn.com/power gr oup/pr oducts.htm to find a suitable alternative. output input output output output efficiency regulation model power voltage voltage current current (max.) line load number (9,10) (max.) (min.) (max.) (2) 15 w 10.8-13.2 vdc 0.8-1.8 vdc 0 a 8 a 87% ?0 mv ?2 mv PTV12010L 44 w 10.8-13.2 vdc 1.2-5.5 vdc 0 a 8 a 92% ?0 mv ?2 mv ptv12010w
file name: ptv12010w.pdf rev (02): 19 dec 2005 for the most current data and application support visit www.artesyn.com/powergroup/products.htm d c-dc converters pola non-isolated 3 new product figur e 2 - safe operating ar ea v in = 12 v , output voltage = 3.3 v (see note a) figur e 1 - safe operating ar ea v in = 12 v , output voltage = 5 v (see note a) figur e 4 - efficiency vs load current v in = 12 v (see note b) figure 3 - safe operating area vin = 12 v, output voltage = 1.8 v (see note a) ptv12010 12 vin single output n n o o t t e e s s a soa curves represent the conditions at which internal components are within the ar tesyn derating guidelines. b characteristic data has been developed from actual products tested at 25 . this data is considered typical data for the converter. ptv12010w characteristic data figure 5 - standard application t e m p e r a t u r e ( o c ) nat conv 2 00 lfm 1 00 lfm 400 lfm output current (a) 20 30 40 50 60 70 80 90 012345678 t e m p e r a t u r e ( o c ) output current (a) 20 30 40 50 60 70 80 90 0123456 78 n at conv 1 00 lfm 2 00 lfm 4 00 lfm e f f i c i e n c y ( % ) output current (a) 5.0v 3.3v 1.8v 1.2v 70 80 90 100 02 6 vout 60 50 48 2 3 c2 10uf ceramic (requi red) c3 100uf optional vin vo rset 1% 0.05w t rack c1 100uf (requi red) gnd inhibit gnd l o a d ptvxx010 5 4 1 6 7 8 gnd inhibit vo adj vo vin t rack t e m p e r a t u r e ( o c ) output current (a) 20 30 40 50 60 70 80 90 02 6 48 nat conv 100 lfm 200 lfm 400 lfm
for the most current data and application support visit www.artesyn.com/powergroup/products.htm d c-dc converters pola non-isolated 4 new product file name: pth12010wl.pdf rev (06): 07 feb 2005 ptv12010 12 vin single output figure 6 - safe operating area vin = 12 v, output voltage 1.8 v (see note a) n n o o t t e e s s a soa cur ves represent the conditions at which internal components are within the ar tesyn derating guidelines. b characteristic data has been developed from actual products tested at 25 . this data is considered typical data for the converter. figure 7 - efficiency vs load current vin = 12 v (see note b) PTV12010L characteristic data figur e 8 - standar d application 2 3 c2 1 0uf ceramic (requi red) c 3 1 00uf optional v in v o rset 1 % 0.05w t rack c1 1 00uf ( requi red) g nd inhibit gnd l o a d ptvxx010 5 4 1 6 7 8 g nd inhibit v o adj v o v in t rack e f f i c i e n c y ( % ) output current (a) 1.2v 1 .0v 0.8v 7 0 80 9 0 100 02 6 vout 60 50 48 t e m p e r a t u r e ( o c ) output current (a) 20 30 40 50 60 70 80 90 02 6 48 n at conv 100 lfm 200 lfm 4 00 lfm
file name: ptv12010w.pdf rev (02): 19 dec 2005 please consult our website for the following items: 4 application note www.artesyn.com datasheet ?artesyn technologies ? 2005 the infor mation and specifications contained in this datasheet ar e believed to be cor rect at time of publication. however, artesyn technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. the information and specifications contained or described herein are subject to change in any manner at any time without notice. no rights under any patent accompany the sale of any such product(s) or information contained herein. for the most current data and application support visit www.artesyn.com/powergroup/products.htm d c-dc converters pola non-isolated 5 new product ptv12010 12 vin single output figure 9 - mechanical drawing and pinout table pin connections pin no. function 1 gr ound 2 vout 3 vout 4 vo adjust 5 track 6 gr ound 7 inhibit 8vin front view side view 0 .330 0.008 (8.38 0.20) 0.100 (2.54) 0.100 (2.54) 1234 6 578 p cb 0.150 (3.81) 0.400 (10.16) 0.900 (22.86) 0.025 (0.64) min 8 places plated through hole dimensions in inches (mm) tolerances (unless otherwise specified) 2 places 0.030 ( 0.76) 3 places 0.010 ( 0.25) 0.020 (0.51)
|
